Bolt Circle Calculator: Hole Coordinates and Diameter

A bolt circle is the circle that passes through the centres of a ring of equally spaced holes. Enter the number of holes, the bolt circle diameter and the angle of the first hole, and the calculator lists X and Y for every hole, the angle between holes and their centre-to-centre distance.

Bolt circle hole coordinates

Use one unit throughout, mm or inches. Angles run counter-clockwise from 3 o’clock (the +X axis).

12345660°6 holes on Ø100Hole 1 at 0°, then every 60°Neighbours 50 apart
Angle between holes60°
Centre to centre, neighbouring holes50
HoleAngleXY
10°500
260°2543.3013
3120°-2543.3013
4180°-500
5240°-25-43.3013
6300°25-43.3013

Bolt circle diameter from a measured part

Measure centre to centre between two neighbouring holes and enter the hole count.

Bolt circle diameterØ100

What is a bolt circle?

A bolt circle is an imaginary circle through the centres of a set of holes spaced evenly around a common centre, as on a flange, a wheel hub or a motor mount. Its size is the bolt circle diameter, also written B.C., BCD or PCD (pitch circle diameter).

Two numbers fix the pattern: how many holes there are and the diameter of the circle. A third, the angle of the first hole, fixes how the pattern is turned. Everything else, each hole’s X and Y and the spacing between holes, follows from those.

How do you calculate bolt circle hole coordinates?

Divide 360° by the number of holes to get the angle between them. Each hole sits at the first-hole angle plus a whole number of those steps, and its coordinates are X = (D ÷ 2) × cos(angle) and Y = (D ÷ 2) × sin(angle), measured from the centre of the circle.

Worked example: 6 holes on a Ø100 bolt circle, first hole at 0°. The step is 60° and the radius is 50. Hole 1 is at X 50, Y 0. Hole 2 is at 60°: X = 50 × cos 60° = 25 and Y = 50 × sin 60° = 43.3013. Hole 3, at 120°, is at X −25, Y 43.3013, and hole 4 is opposite hole 1 at X −50, Y 0.

If the centre of the circle is not at zero, add its X and Y to every hole. The calculator does that when you fill in the centre.

How is a bolt circle shown on a drawing?

The bolt circle is drawn as a thin chain line, long and short dashes, through the hole centres, with its diameter dimensioned. One hole carries the callout for all of them, such as 6X Ø9 THRU, and a note or an angle shows that the holes are equally spaced.

12345660°6X Ø9 THRUEQ SP ON Ø100 B.C.Chain line: the bolt circleHole 1 at 0°, then every 60°Neighbours 50 apart
6X means six holes of the same size. EQ SP (equally spaced) and the Ø100 B.C. give everything needed to place them.

6X is the count, Ø9 the hole size and THRU the depth. Older prints spell it out, “6 HOLES EQUALLY SPACED ON A 100 DIA B.C.”; newer ones dimension the chain circle and one angle. A threaded pattern swaps the hole size for a thread, covered in thread callouts. When the location matters, each hole also gets a position tolerance, which the true position calculator checks.

How do you measure a bolt circle diameter?

With an even number of holes, measure centre to centre between two opposite holes: that distance is the bolt circle diameter. With an odd number there is no opposite hole, so measure between two neighbouring holes and divide by sin(180° ÷ N), the factor in the table below.

HolesAngle between holesNeighbour distance ÷ diameter
3120°0.8660
490°0.7071
572°0.5878
660°0.5000
845°0.3827
1036°0.3090
1230°0.2588

Example: a 5-hole pattern measures 58.7785 between neighbours, and 58.7785 ÷ 0.5878 gives Ø100. To measure centre to centre without finding centres, measure from the edge of one hole nearest its neighbour to the far edge of that neighbour, which is the same distance when the holes are the same size.

Where does the first hole go?

Wherever the drawing puts it. With no angle shown, a hole is usually drawn on a centre line. Many flanges instead have the holes straddle the centre lines, which puts the first hole at half the spacing angle: 45° for 4 holes, 22.5° for 8.

Four holes on a Ø100 circle starting at 45° land at X ±35.3553, Y ±35.3553, a square pattern 70.7107 on a side. Enter 90 to start at 12 o’clock, or a negative angle to start below the horizontal centre line.

Frequently asked questions

What is the formula for bolt circle coordinates?

For hole number i, counting from zero, the angle is the first-hole angle plus i × 360° ÷ N. Then X = centre X + (D ÷ 2) × cos(angle) and Y = centre Y + (D ÷ 2) × sin(angle), where D is the bolt circle diameter and N the number of holes.

How do you find the bolt circle diameter with an odd number of holes?

Measure centre to centre between two neighbouring holes and divide by sin(180° ÷ N). On a 5-hole pattern that is the distance ÷ 0.5878, so holes 58.7785 apart sit on a Ø100 bolt circle.

How far apart are the holes on a bolt circle?

The straight centre-to-centre distance between neighbours, the chord, is D × sin(180° ÷ N). Six holes on a Ø100 circle are 50 apart; four holes on the same circle are 70.7107 apart.

Is a bolt circle the same as a pitch circle diameter?

Yes. Bolt circle (B.C.), bolt circle diameter (BCD) and pitch circle diameter (PCD) all name the diameter of the circle through the centres of the holes. PCD is the usual term on metric and wheel drawings.

Which way do the angles run?

Counter-clockwise from the 3 o’clock position, the +X axis, which is how drawings and CNC controls measure angles. For a pattern numbered clockwise, enter the same first-hole angle and read the list from hole 1 backwards.

Does it work in inches and millimetres?

Yes. The math has no units: enter the diameter and the centre in inches and the coordinates come out in inches; enter millimetres and they come out in millimetres. Do not mix the two.

Have a drawing of the part but no CAD model?

Upload the drawing to Drawing to STEP: a PDF, PNG or JPG becomes a 3D STEP model, with files from $29.99. The model has every hole of the pattern in place; keep the drawing with it, because the drawing carries the tolerances.