Metal Weight Calculator: Steel, Aluminum and Stainless
Metal weight is the cross-section area times the length times the density: a 10 ft length of 1 inch carbon steel round bar weighs 26.7 lb (12.1 kg). The calculator below does plate, bar, tube, pipe and angle in steel, stainless, aluminum, brass, bronze, copper, cast iron, titanium and zinc, in pounds and kilograms.
Metal weight calculator
Pick the material and shape, enter the sizes and length, and the weight updates as you type.
| Material | |
| Shape | |
| Sizes in | |
| Weight per piece | 26.73 lb (12.12 kg) |
| Total for 1 | 26.73 lb (12.12 kg) |
| Per foot / per metre | 2.67 lb/ft (3.98 kg/m) |
How do you calculate the weight of metal?
Multiply the area of the cross-section by the length to get the volume, then multiply by the material’s density. Keep the units together: square inches times inches times pounds per cubic inch gives pounds, and square millimetres times millimetres times grams per cubic millimetre gives grams.
For 1 inch steel round bar, 10 feet long: the area is π/4 × 1² = 0.785 in², the length is 120 in, so the volume is 94.2 in³. Steel weighs 0.2836 lb/in³, so the bar weighs 26.7 lb, or 2.67 lb per foot.
How much does steel weigh?
Carbon steel weighs 0.2836 lb per cubic inch (7.85 g/cm³), about 490 lb per cubic foot. Steel plate weighs 40.84 lb per square foot for each inch of thickness, and 7.85 kg per square metre for each millimetre: a 1 m × 1 m sheet of 10 mm plate is 78.5 kg.
| Size (in) | Round bar (lb/ft) | Square bar (lb/ft) | Hex bar (lb/ft) |
|---|---|---|---|
| 1/2 | 0.67 | 0.85 | 0.74 |
| 3/4 | 1.50 | 1.91 | 1.66 |
| 1 | 2.67 | 3.40 | 2.95 |
| 1-1/2 | 6.01 | 7.66 | 6.63 |
| 2 | 10.69 | 13.61 | 11.79 |
| 3 | 24.06 | 30.63 | 26.53 |
| Plate thickness (in) | Steel (lb/ft²) | Stainless 304 (lb/ft²) | Aluminum 6061 (lb/ft²) |
|---|---|---|---|
| 1/8 | 5.10 | 5.16 | 1.76 |
| 1/4 | 10.21 | 10.31 | 3.51 |
| 3/8 | 15.31 | 15.47 | 5.27 |
| 1/2 | 20.42 | 20.63 | 7.02 |
| 1 | 40.84 | 41.25 | 14.05 |
Stainless steel is about 1% heavier than carbon steel, and the grade barely moves it: 304 is 7.93 g/cm³ and 316 is 7.98. For sheet by gauge number, the sheet metal gauge chart gives the thickness to enter here. Its steel weights are a little higher, 41.82 lb per square foot per inch against 40.84 here, because the steel gauge is defined by that nominal weight; this calculator uses the density of solid steel, so a gauge sheet comes out about 2.4% lighter here.
How much does aluminum weigh?
6061 aluminum weighs 0.0975 lb per cubic inch (2.70 g/cm³), about a third of steel. Aluminum plate weighs 14.05 lb per square foot for each inch of thickness, so 1/4 inch plate is 3.51 lb/ft². The alloy changes it only slightly: 5052 is 2.68 and 7075 is 2.81 g/cm³.
What is the density of common metals?
The table gives the typical density of each material in the calculator, in g/cm³ and lb/in³, and the weight of a square foot of plate one inch thick. A specific grade can differ from these typical values by about 1–3%.
| Material | Grades | g/cm³ | lb/in³ | Plate, lb/ft² per inch |
|---|---|---|---|---|
| Carbon steel | A36, 1018, 1045, mild steel | 7.85 | 0.2836 | 40.8 |
| Stainless steel 304 | 304, 304L, 303 | 7.93 | 0.2865 | 41.3 |
| Stainless steel 316 | 316, 316L | 7.98 | 0.2883 | 41.5 |
| Aluminum 6061 | 6061, 6063, 6082 | 2.70 | 0.0975 | 14.0 |
| Aluminum 5052 | 5052, 5083 | 2.68 | 0.0968 | 13.9 |
| Aluminum 7075 | 7075 | 2.81 | 0.1015 | 14.6 |
| Brass | C360, C260 | 8.50 | 0.3071 | 44.2 |
| Bearing bronze | C93200 (SAE 660) | 8.93 | 0.3226 | 46.5 |
| Copper | C110, C101 | 8.94 | 0.3230 | 46.5 |
| Gray cast iron | Class 30, GG25 | 7.20 | 0.2601 | 37.5 |
| Titanium | Ti-6Al-4V (Grade 5) | 4.43 | 0.1600 | 23.0 |
| Zinc alloy | Zamak 3 | 6.60 | 0.2384 | 34.3 |
What are the area formulas for each shape?
Each shape’s weight is its cross-section area times its length times the density. These are the areas the calculator uses, with all sizes in the same unit. Tubes and angles are taken with sharp corners.
| Shape | Cross-section area |
|---|---|
| Plate, sheet or flat bar | thickness × width |
| Round bar | π/4 × diameter² |
| Square bar | side² |
| Hex bar | 0.866 × across flats² |
| Round tube or pipe | π/4 × (OD² − ID²), where ID = OD − 2 × wall |
| Square or rectangular tube | width × height − (width − 2 × wall) × (height − 2 × wall) |
| Angle | thickness × (leg A + leg B − thickness) |
How accurate is a calculated metal weight?
Usually within a few percent. The density of a specific grade can differ from the typical value by 1–3%, mill stock runs a little over or under its nominal size, and real tubes and angles have rounded corners that make them slightly lighter than the sharp-cornered formula.
- Corner radii. Structural tube and angle tables account for the radius, so they read a percent or two below this calculator on light sections.
- Coatings. Hot-dip galvanizing adds about 2 oz per square foot of surface on structural steel; G90 galvanized sheet carries about 0.9 oz per square foot, both sides together. Paint and plating add little.
- Shipping weight. For freight, round up and add the crate or pallet.
How do you find the weight of a finished part?
Measure its volume in a 3D model and multiply by the density. Stock calculators like this one only work for whole bars and plates; a machined, cast or formed part has holes, pockets and bends that change its volume, and the model is the only reliable way to account for them.
If you have the drawing but no model, Drawing to STEP builds one, and every new conversion comes with a bill of materials listing each part’s material and weight where the drawing gives them. The bill of materials example shows one for a real assembly drawing.
Frequently asked questions
How much does a 4x8 sheet of 1/4 inch steel weigh?
About 326.7 lb (148.2 kg). Quarter-inch steel plate weighs 10.21 lb per square foot and a 4 × 8 sheet is 32 square feet. The same sheet in 6061 aluminum weighs about 112.4 lb.
How much does steel plate weigh per square foot?
40.84 lb per square foot for every inch of thickness, so 1/4 inch plate is 10.21 lb/ft² and 1/2 inch is 20.42 lb/ft². In metric, steel plate weighs 7.85 kg per square metre for every millimetre of thickness.
How heavy is aluminum compared with steel?
About a third: 6061 aluminum is 2.70 g/cm³ against 7.85 for carbon steel, so an aluminum part weighs 34% of the same part in steel. Aluminum is also less stiff, so a part redesigned in aluminum usually gets thicker and gives back some of the saving.
What is the weight of steel per cubic inch?
0.2836 lb per cubic inch, from a density of 7.85 g/cm³. That is 490 lb per cubic foot and 7,850 kg per cubic metre.
How do I calculate the weight of a pipe?
Take the area of the ring, π/4 × (OD² − ID²), times the length and the density. 2 inch Schedule 40 steel pipe (2.375 in OD, 0.154 in wall) works out to 3.66 lb per foot; pick round tube in the calculator and enter the OD and wall.
Have a drawing and need every part’s weight?
Upload it to Drawing to STEP: a PDF, PNG or JPG becomes a 3D STEP model, with a bill of materials that gives each part’s weight from the model’s volume where the drawing gives the material. On an assembly the weights roll up through its parts list.