ISO 2768 General Tolerances: Chart and Calculator

ISO 2768 sets the tolerance for every dimension a drawing leaves untoleranced. Under the common note ISO 2768-m, a 25 mm length is ±0.2 mm, so 24.8 to 25.2 mm. Enter a size and class below for lengths, radii, chamfers and angles, or read the full chart.

ISO 2768-1 general tolerance

Sizes in millimetres. For an angle, enter the length of its shorter side.

Permitted deviation±0.2 mm
Limits24.8 to 25.2 mm

What is ISO 2768?

ISO 2768 is the standard for general tolerances. Instead of a tolerance on every dimension, the drawing carries one note, such as ISO 2768-m, and every dimension without its own tolerance takes the value from the standard’s tables for its size and class.

Part 1 covers lengths, external radii, chamfer heights and angles in four classes: f (fine), m (medium), c (coarse) and v (very coarse). Part 2 covers geometric tolerances such as flatness and perpendicularity in three classes, H, K and L. A dimension with its own tolerance or fit, such as Ø25 H7, ignores the note.

What is the ISO 2768-1 tolerance chart?

The chart gives the permitted deviation, plus or minus, for linear dimensions in each class. Values are in millimetres. A size on a range boundary belongs to the lower range, so 30 mm uses the 6–30 row; a dash means the class gives no tolerance there, and the drawing must give one.

Size (mm)fmcv
0.5–3±0.05±0.1±0.2—
3–6±0.05±0.1±0.3±0.5
6–30±0.1±0.2±0.5±1
30–120±0.15±0.3±0.8±1.5
120–400±0.2±0.5±1.2±2.5
400–1000±0.3±0.8±2±4
1000–2000±0.5±1.2±3±6
2000–4000—±2±4±8

Below 0.5 mm the standard gives no general tolerance: the size must be toleranced on the drawing.

What does ISO 2768-m mean?

ISO 2768-m puts every untoleranced dimension in the medium class. A 25 mm length is ±0.2 mm, a 100 mm length ±0.3 mm and a 500 mm length ±0.8 mm. It is the usual default for machined parts, and the tolerance most shops quote against when a drawing says nothing else.

What tolerance applies to radii and chamfers?

External radii and chamfer heights have their own, looser table. In classes f and m, a 2 mm chamfer is ±0.2 mm and a 10 mm radius ±1 mm; classes c and v double those values.

Size (mm)f and mc and v
0.5–3±0.2±0.4
3–6±0.5±1
over 6±1±2

What are the ISO 2768 angular tolerances?

Angles are toleranced by the length of the shorter side of the angle, because a short leg makes the same angle error a smaller distance. In class m, an angle with a 20 mm shorter side is ±0°30′ and one with a 200 mm side ±0°10′.

Shorter side (mm)f and mcv
up to 10±1°±1°30′±3°
10–50±0°30′±1°±2°
50–120±0°20′±0°30′±1°
120–400±0°10′±0°15′±0°30′
over 400±0°5′±0°10′±0°20′

What does ISO 2768-mK mean?

The second letter is the geometric class from ISO 2768-2: H is the tightest, K the middle and L the loosest. Under K, a 100 mm surface must be flat within 0.2 mm, and circular run-out is held to 0.2 mm at any size.

Length (mm)Straightness and flatness H / K / L
up to 100.02 / 0.05 / 0.1
10–300.05 / 0.1 / 0.2
30–1000.1 / 0.2 / 0.4
100–3000.2 / 0.4 / 0.8
300–10000.3 / 0.6 / 1.2
1000–30000.4 / 0.8 / 1.6
Shorter side (mm)Perpendicularity H / K / LSymmetry H / K / L
up to 1000.2 / 0.4 / 0.60.5 / 0.6 / 0.6
100–3000.3 / 0.6 / 10.5 / 0.6 / 1
300–10000.4 / 0.8 / 1.50.5 / 0.8 / 1.5
1000–30000.5 / 1 / 20.5 / 1 / 2

Circular run-out: H 0.1, K 0.2, L 0.5 mm. Values in millimetres. ISO 2768-2 was withdrawn in 2021 and replaced by ISO 22081, but drawings made before then still say ISO 2768-mK, and shops still read them with these tables.

How is ISO 2768 written on a drawing?

The note sits in or beside the title block, usually after “unless otherwise specified”: ISO 2768-m for lengths and angles only, or ISO 2768-mK to add the geometric class. Older drawings may write it as DIN ISO 2768-mK or ISO 2768-1-m.

UNLESS OTHERWISE SPECIFIED:DIMENSIONS IN MMISO 2768-mKPART NAMEMATERIALSCALE 1:1m = linear class, K = geometric class
The general-tolerance note sits in or beside the title block and covers every dimension that carries no tolerance of its own.

For the other callouts on a print, see engineering drawing symbols; for a fit such as Ø25 H7, use the ISO fit calculator; and for how tolerances add up along a chain of dimensions, see tolerance stack-up basics.

Which ISO 2768 class should I use?

Pick the loosest class the part can take, because tighter tolerances cost machining time and inspection. Class m suits most machined parts; f is for precision work; c suits rough machining, sawn stock and fabricated parts; v is for the roughest work, where only the shape matters.

Put a tolerance of its own on any dimension that matters to function, such as a bearing bore or a mating face, rather than tightening the whole drawing to class f.

Frequently asked questions

What is ISO 2768?

ISO 2768 is the international standard for general tolerances: the tolerance a dimension gets when the drawing gives it none of its own. Part 1 covers lengths, radii, chamfers and angles in four classes, f, m, c and v. Part 2 covered flatness, straightness and similar form tolerances in classes H, K and L.

What does ISO 2768-m mean?

ISO 2768-m means every untoleranced dimension on the drawing gets the medium class of ISO 2768-1. A 25 mm length is then ±0.2 mm, a 100 mm length ±0.3 mm, and an angle whose shorter side is 20 mm ±0°30′.

What does ISO 2768-mK mean?

The m is the medium class for lengths and angles from ISO 2768-1, and the K is the middle class for geometric tolerances from ISO 2768-2. Under K, a 100 mm surface must be flat within 0.2 mm and circular run-out is held to 0.2 mm.

Which ISO 2768 class is most common?

Class m, medium, is the usual default for machined parts, and ISO 2768-mK is the most common note on metric drawings. Class f is chosen for precision work, c for rough machining and fabricated parts, and v for the roughest work.

Does ISO 2768 apply to holes and fits?

Only to sizes with no tolerance of their own. A hole called out as Ø25 H7 follows ISO 286, not ISO 2768; a plain Ø25 on a drawing with an ISO 2768-m note is ±0.2 mm.

Is ISO 2768 still valid?

ISO 2768-1 is still current. ISO 2768-2 was withdrawn in 2021 and replaced by ISO 22081, but drawings made before then still carry notes such as ISO 2768-mK, and shops read them with the part 2 tables.

Does ISO 2768 work in inches?

ISO 2768 is defined in millimetres. To use it on an inch part, convert the size to mm, read the tolerance, and divide it by 25.4: ±0.2 mm is about ±0.008 in. Inch drawings usually state their own title-block tolerances instead.

Have a drawing of the part but no CAD model?

Upload the drawing to Drawing to STEP: a PDF, PNG or JPG becomes a 3D STEP model in minutes, with files from $29.99. Keep the drawing with the model: a STEP file carries the shape, and the drawing carries the tolerances.