Open your file — or describe the part you need

Drag in a STEP, STL, IGES, OBJ, DXF, BREP, or GLB file to view it in 3D — free, no signup to look. No file yet? Describe your part in Studio →

What Is a Title Block? Every Field on an Engineering Drawing, Explained

A title block is the boxed table in the lower right corner of an engineering drawing that names the part and sets the rules for the whole sheet: drawing number, revision, units, material, scale, projection and default tolerances. This guide draws a complete block, explains every field and the revision block beside it, and lists what a good template holds.

What is a title block on an engineering drawing?

The title block is the identity card and rule book of a drawing. It sits in the lower right corner, inside the border, and every number elsewhere on the sheet depends on it: the units it states, the tolerances it sets and the revision it names. A shop reads it before anything else.

UNLESS OTHERWISESPECIFIED:DIMENSIONS ARE IN INCHESTOLERANCES:.XX ±.01.XXX ±.005ANGLES ±0.5°INTERPRET PER ASME Y14.5MATERIAL6061-T6 ALUMINUMFINISHCLEAR ANODIZEDO NOT SCALE DRAWINGDRAWNJS 03/12/26CHECKEDMK 03/14/26APPROVEDRL 03/16/26THIRD ANGLECOMPANYNORTHWIND MFG. CO.TITLEBRACKET, MOUNTINGSIZEBDWG NO.10427-01REVCSCALE1:1WEIGHT0.42 LBSHEET1 OF 1
A typical inch title block. Metric blocks hold the same fields, with the units in millimetres and a general tolerance class in place of the decimal-place table.

The block above is laid out the way most inch drawings in the US do it: the tolerance block on the left, the names and the projection symbol in the middle, and the company, title, drawing number and revision on the right, where they are easy to find when sheets are stacked or folded. Company templates move fields around, but the same information is almost always there.

What information goes in a title block?

A title block holds what identifies the drawing and what applies to the whole part: the company, title, drawing number, revision, sheet size, scale and sheet count, the names of the people who drew, checked and approved it, material, finish, the projection symbol and the default tolerances.

FieldWhat it tells youExample
Company nameWho owns the design and answers questions about itNORTHWIND MFG. CO.
TitleWhat the part is, usually noun firstBRACKET, MOUNTING
Drawing numberThe part’s identity; orders and files use it10427-01
RevisionWhich version this sheet showsC
SizeThe sheet the drawing was made forB (11 × 17 in)
ScaleHow big the views are drawn, for orientation only1:1, 1:2, NTS
SheetHow many pages belong to this drawing1 OF 3
Drawn, checked, approvedWho made, reviewed and released it, with datesJS 03/12/26
MaterialAlloy, grade or plastic, often by specification6061-T6 ALUMINUM
FinishCoating, plating or treatment for the whole partCLEAR ANODIZE
Projection symbolWhere the views sit relative to each otherThird angle
Tolerance blockUnits and the default tolerance for untoleranced sizes.XX ±.01
WeightFinished weight, for shipping and checking0.42 LB
  • Title, noun first. “BRACKET, MOUNTING” rather than “MOUNTING BRACKET”, so a list of drawings sorts by what the parts are.
  • Drawing number vs part number. Often the same. When they differ, the part number is in a parts list or a dash number after the drawing number, such as -01 and -02 for two sizes on one sheet.
  • CAGE code. On US defense work, a five-character code next to the drawing number identifies the company that owns the design.
  • Next assembly and used on. Some blocks name the assembly the part goes into, which helps when a part is replaced on an old machine.

What does “unless otherwise specified” mean in the tolerance block?

“Unless otherwise specified” means the units and tolerances listed under it apply to every dimension on the sheet that has no tolerance of its own. A dimension with its own limits, a fit such as H7 or a geometric tolerance frame overrides the block for that feature only.

  • Decimal places set the tolerance. With .XX ±.01 and .XXX ±.005, a size written 1.50 may be 1.49 to 1.51, and 1.500 must be 1.495 to 1.505. Adding a zero is a tighter, more expensive requirement.
  • Fractions and angles. Older inch drawings add a fraction line, often ±1/64, and every block gives an angle tolerance, commonly ±0.5° or ±1°.
  • Metric blocks. Usually one line such as “general tolerances ISO 2768-m”, which sets limits by size range. Look them up in the ISO 2768 tolerance calculator.
  • Interpretation. “Interpret per ASME Y14.5” names the dimensioning and tolerancing standard the symbols follow; a careful block adds its edition year.
  • Other defaults. Edge breaks (“break all sharp edges .005-.015”), inside corner radii, and a default surface finish symbol, explained in the surface finish chart.

A tolerance block left at the template default is one of the most common drawing errors: a sheet metal part with ±.005 on every size costs far more to make than one at ±.010. When a drawing’s defaults look wrong for the part, ask before quoting.

What is a revision block?

A revision block is the change history of the drawing, usually in the upper right corner: one row per revision with a letter, a short description of what changed, a date and an approval. The newest letter must match the REV box in the title block, and that is the version to make.

REVISIONSREVDESCRIPTIONDATEAPPROVEDAINITIAL RELEASE01/15/24RLBHOLE Ø.250 WAS Ø.20106/02/25RLCADDED CHAMFER, NOTE 403/12/26RL
Newest revision at the bottom on most sheets; its letter must match the REV box in the title block.
  • Letters, not numbers. Under ASME Y14.35 revisions go A, B, C, skipping I, O, Q, S, X and Z because they read like numbers. After Y comes AA. Many companies show the first release as a dash or as A.
  • The description says what moved. “HOLE Ø.250 WAS Ø.201” tells a shop exactly what to change on parts already in progress.
  • Revision flags. A small triangle with the letter, placed next to each changed feature, shows where on the sheet the change is.
  • Match the purchase order. A shop that makes rev B when the order says rev C has made scrap, so the letter is checked at quoting and again at inspection.

How do ASME and ISO title blocks differ?

ASME and ISO title blocks carry much the same information in the same corner. The differences are in the sheet sizes, the usual units and projection, and how default tolerances are written: by decimal places on ASME inch drawings, by a general tolerance class on ISO metric ones.

WhatASME (US)ISO
Sheet sizesA to E: 8.5 × 11 in up to 34 × 44 inA4 to A0: 210 × 297 mm up to 841 × 1189 mm
Usual unitsInchesMillimetres
Usual projectionThird angleFirst angle
Default tolerancesBy decimal places: .XX, .XXXA general tolerance class, such as ISO 2768-m
Fields set byASME Y14.1 and the company templateISO 7200
RevisionsASME Y14.35: letters, revision blockA revision index field and a change table
First angleThird angle
The cone is drawn the same way in both; the end view (the circles) moves.

The projection symbol in the block is the one field that changes how you read the views: a first angle drawing read as third angle puts every side view on the wrong side of the part. How to tell them apart is in first vs third angle projection. ISO 7200 keeps the mandatory fields short, among them the legal owner, the drawing number, the date of issue and the sheet number, and leaves the revision index optional.

How do you make a title block template?

Make one template per sheet size in your CAD program’s drawing format, with the border, the title block in the lower right corner, a revision block in the upper right, and the fields linked to the model’s properties so the number, title and material fill themselves in.

  1. Pick the sheet sizes you use. Usually A and B, or A4 and A3, plus one larger size for assemblies.
  2. Draw the border and zones. Letters down the side and numbers along the top, so a note can say “see zone C3”.
  3. Lay out the block. Identity fields (number, revision, title) at the right, where they show on a folded sheet.
  4. Link the fields. Drawing number, title, material, weight and the drawn-by name come from the model, so they cannot disagree with it.
  5. Set honest defaults. Write the tolerance block for the work you actually do, and state the units in words.
  6. Keep text readable. Around 3 mm (0.12 in) tall or more, so the block still reads after copying and scanning.

For complete sheets to copy the layout from, see the sample engineering drawings. An assembly adds a parts list above the title block; that is covered in the guide to assembly drawings.

What do you need from the title block to model a part in 3D?

To turn a drawing into a 3D model you need the units, the projection method, the revision and the sheet count from the title block. The units fix the size of every number, the projection fixes which view is which side, and the sheet count tells you whether a view is on another page.

  • Units. A model made in millimetres from an inch drawing is 25.4 times too small. Inch drawings usually show .250 with a leading decimal point; metric ones 6.35 or 6.
  • Projection. Decides whether the view to the right of the front view is the right side or the left side.
  • Revision. The model should carry the same letter as the drawing it came from.
  • Material and tolerances. Not part of the shape, but they go with the model to whoever quotes it, together with the drawing.

Old prints often have a block that is faded, half filled in or missing its units. The guide to old mylar drawings covers how to read legacy sheets, and how to read engineering drawings walks through a whole sheet in order.

What title block mistakes cause wrong parts?

Most title block errors are copied from a template or an old drawing: units that are not stated, a revision letter that does not match the revision block, a tolerance block too tight for the part, a projection symbol that does not match the views, and a material left as “see note” with no note.

  1. No units stated. Every number is then a guess; say inches or millimetres in words.
  2. REV box and revision block disagree. The shop cannot tell which one is current.
  3. Template tolerances. ±.005 on every size of a plate that only needs ±.03 in most places.
  4. Wrong projection symbol. A metric template reused for a US part, or the reverse.
  5. A scale that does not match the views. Harmless if nobody measures the print, but a warning that the sheet was not checked.
  6. Blank approvals. A drawing nobody checked or released is a draft, not a print to make parts from.

The symbols the title block refers to, from the projection cone to the finish mark, are drawn in the engineering drawing symbols chart.

Frequently asked questions

What is a title block on a drawing?

A title block is the boxed table in the lower right corner of an engineering drawing. It names the part, its drawing number and revision, and states the units, material, finish, scale, projection method and default tolerances that apply to everything else on the sheet.

Where is the title block located?

In the lower right corner of the sheet, inside the border, on both ASME and ISO drawings. That is where the drawing number can be read when a sheet is folded or filed. The revision block usually sits in the upper right corner.

What does "unless otherwise specified" mean in a title block?

It means the values that follow, such as the units, the default tolerances, the finish and the edge breaks, apply to every feature on the sheet that does not carry its own value. A dimension with its own tolerance overrides the block.

What is the difference between a title block and a revision block?

The title block identifies the drawing and sets its defaults: number, title, material, units and tolerances. The revision block is the change history: one row per revision with a letter, a description, a date and an approval. The newest letter must match the REV box in the title block.

What does "do not scale drawing" mean?

It means no size may be measured off the paper or the screen with a ruler. Prints and scans stretch, and a view drawn at 1:2 on a B-size sheet is a different size again on a letter printout. If a size you need is not written, ask the person who issued the drawing.

What should a title block template include?

At least the company name, drawing title, drawing number, revision, sheet size, scale, sheet number, the drawn, checked and approved names with dates, material, finish, the projection symbol and a tolerance block that states the units and default tolerances.

Have a drawing like this and need a 3D model?

Upload it to Drawing to STEP from PartWork.ai. You get a STEP and an STL of the part, from $29.99, in the units the title block states and checked against every view and dimension on the drawing.

  • Any print. A PDF, PNG or JPG, from CAD, a scanner or a phone photo, new or decades old.
  • Questions, not guesses. When the units, a revision or a dimension is faded, missing or conflicting, we ask you before the model is finished.
  • Assemblies too. Assembly drawings are in scope when the parts are dimensioned.

It does not do freeform shapes yet. For other routes to a model, see how to convert a PDF to CAD and CAD drafting services.

Export-controlled drawings (ITAR/EAR) aren’t accepted.

Drawing to STEP

Convert a drawing →